Amplifier Research 75S1G6C RF-kraftförstärkare
Amplifier Research 75S1G6C RF Power Amplifier
Begär en offert
Amplifier Research 75S1G6C är en 75-watts Class A RF-kraftförstärkare som täcker 1.0–6.0 GHz med missanpassningstolerans och fjärrkontroll via Ethernet, USB, GPIB och RS-232.
Produktinformation
| Modell | 75S1G6C |
| Tillverkare | Amplifier Research |
| Kategori | RF- och mikrovågstestutrustning |
| Tillgänglighet | Tillverkas på beställning |
Beskrivning
Översikt
Amplifier Research 75S1G6C är en solid-state Class A RF-kraftförstärkare utformad för applikationer som kräver momentan bandbredd, högt förstärkning och överordnad linjäritet. Den levererar minst 75 watts över sin 1.0–6.0 GHz arbetsbandbredd med inbyggt skydd mot ingångsöverbelastning och olika felvillkor inklusive övertemperatur och strömförsörjningsfel. Den modulära designen möjliggör enkel underhåll och service.
Huvudfunktioner
- 75 watts CW över 1.0–6.0 GHz bandbredd
- Class A design för exceptionell linjäritet och låga övertoner
- 100% missanpassningstolerant—fortsätter driften in i höga VSWR-belastningar inklusive öppna och kortslutningskretsar
- Inbyggd felövervakning och skydd från övertemperatur och strömförsörjningsfel
- Flera fjärrkontrolfunktioner: Ethernet, USB, GPIB (IEEE-488), fiberoptisk seriell och RS-232
- Låg akustisk bulleroperering
- Modulär design för enkel underhåll
Tillämpningar
- EMC-testning (militär, luftfart, fordon, kommersiell)
- Strålad och ledd EMC-testning
- Allmän RF-, antenn- och komponenttestning
- Trådlös och kommunikationskomponent- och delsystemtestning
- 5G-testningsapplikationer
Specifikationer
| Front Panel Display | A front panel display indicates the operational status and fault conditions. All amplifier control functions, and status indications are available remotely using GPIB/IEEE-488, RS-232, fiber-optic serial, USB, or Ethernet. Interface connectors are located on the back panel. Local and remote operation is managed by a switch on the front panel. |
| Multiple Purpose Amplifier | This is a multiple purpose amplifier. The low level of spurious signals and linearity make it ideal for use as a driver in testing wireless and communication components and subsystems. By covering such a wide bandwidth, it is suitable for 5G testing applications. Due to the Class A design, it is also suitable for EMC Test applications where continued operation into high VSWR loads including open and short circuits is required. |
| Export Classification | The export classification for this equipment is 3A001. These commodities, technology or software are controlled for export in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited. |
| Feature | SymbolMinimumTypicalMaximum |
| Rated Power Output | PSAT75W85W>125W |
| Input for Rated Output | Pin----1.0mW 0dBm |
| Power Output @ 1 dB Compression | P1dB50W70W>100W |
| Power Output @ 3 dB Compression | P3dB65W85W>120W |
| Operating Frequency | BW1.0GHz--6.0GHz |
| Gain (Small Signal) | 51dB54dB56dB |
| Flatness | ∆G--±1.5dB±2.5dB |
| Input Impedance | Z in--50Ω 1.5:1 VSWR -- 2.0:1 VSWR |
| Output Impedance | Z out--50Ω-- |
| 3rd Order Intercept | IP3--+56dBm-- |
| Noise Figure | NF--10dB-- |
| Spurious | ---73dBc-- |
| Power Consumption | PD----450W |
| Feature | Parameter |
| Cooling | Forced air (self-contained fans) Side inlets / rear outlet Δt = +7°C (typical) |
| Regulatory Compliance | EMC: EN 61326-1 Safety: UL 61010-1 CAN/CSA C22.2 #61010-1 CENELEC EN 61010-1 RoHS: Directive 2011/65/EU Export: 3A001 |
| Connector Interfaces | RF input: N female (50 Ω) RF output: N female (50 Ω) IEEE-488: 24-pin female RS-232: 9-pin subminiature D female RS-232 (fiber optic): ST USB 2.0: Type B Ethernet: RJ-45 Interlock: 15-pin subminiature D female AC: C14 |
Begär en offert
Amplifier Research 75S1G6C RF-kraftförstärkare
Svar inom 24 timmar
Inga förpliktelser
Direkt kontakt